Thank you so much for your involvement with the Owner's Club Forum! We hope you've gotten some great information and had the chance to interact with other owners on the current system.

New guy project, Part II

Team36Grit
Team36Grit Member Posts: 68 ✭✭
Well see.... Hull flipped photo P6180002_zps39b21c23.jpg photo P6180003_zpscf4f7bed.jpg Sat on wagon to move for painting (once the time comes photo P6180007_zps7febb628.jpg
«1

Comments

  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Painted photo P6280003_zps5bcd60c9.jpg photo P6270003_zps8bc6cddf.jpg Trailer painted photo P6170007_zps95e201b1.jpg photo P6170005_zps050d89f9.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    New brake assemblies photo P6270007_zps7dc62a68.jpg Bunks and carpet photo P6250005_zpsdfaf94d3.jpg photo P7030001_zps5276c23b.jpg Bedliner on steps and fenders photo P7020002_zpsa0e2c0ca.jpg photo P7020001_zps0f972125.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Back on trailer photo P7090002_zpsb9e64915.jpg New deck drains photo P7070004_zps1d411763.jpg Curb built over ski locker, 3 trolling batteries will set here, under console photo P7050007_zps7dfeeb3d.jpg Deck going back onto hull photo P7130014_zpsa90e975e.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Gray trim and red stripe painted photo P7120006_zps101df247.jpg photo P7120001_zpsccfe024a.jpg photo P7120009_zps60c188fa.jpg photo P7120008_zps6aede968.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Outer edge of deck painted photo P7170004_zps254076d6.jpg photo P7170004_zps0d4ce3d4.jpg photo P7170002_zps258f8886.jpg photo P7170001_zpsee6747ff.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Made the cover for fuel line opening, was "open" before. photo P7150002_zps1b86b4e5.jpg Brazed brass rod to drain plug, no wrench to find. photo P7140001_zpsff76e94b.jpg And carry a spare in the bilge photo P7140002_zpsa55b9958.jpg LED Trailer lighting finished photo P7140007_zps3df5c8f2.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Mocked-up windshield made from scrap smoked Lexan. Had to wetsand and buff to remove scratches. It got aluminum angle added to corners (in place of blue masking tape). photo P7220003_zps69602893.jpg Working on console seat photo P7220006_zpsb9ef916d.jpg PVC rod holders on fence at front corners. photo P7220006_zpsb9ef916d.jpg Carpeted motor cover, added doors for storage and access to rear hatches (for batteries) photo P8010001_zps3469b21c.jpg photo P8010003_zpsfe2de431.jpg More smoked Lexan to prevent "reach-throughs" photo P7270002_zpsd1cc2733.jpg photo P7270001_zps4e0b4a5c.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Deck coated with MonstaLiner bed liner (good stuff!) photo P8060007_zpscd655cd4.jpg Console curb was sealed to floor, then lined to prevent any water intrusion. photo P8060008_zpscf0d3b5e.jpg photo P8060003_zps74feb377.jpg photo P8060002_zpsbe924676.jpg photo P8060008_zpscf0d3b5e.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Console set photo P8080003_zps19085970.jpg New fishing seats photo P8090001_zps3593acab.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Spider rigging rod holders installed photo P8130001_zps8d3f6004.jpg Rear nav light stowed under motor well cover photo P8120007_zps2b3d6424.jpg Bow nav light stowed inside door photo P8120006_zpsb90f68c3.jpg 10 gal bait tank made from drink cooler photo P8090006_zpsae759001.jpg photo P8090005_zps51a0e303.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Doors on console photo P8190006_zps1bb604f2.jpg Rear PVC rod holders added photo P8180003_zpse158e391.jpg Bent-up some scrap aluminum for cup holders on front seats photo P8140001_zps88309cf0.jpg Added some non-skid photo P9060001_zpsdc1607d8.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    Fencing was pretty ugly, bought a couple sheets of FRP and glued it to the fencing. Has held-up so far from below freezing to 100*. photo P8240004_zps4ea84234.jpg Made jigs to clamp it while adhesive cured, photo P8240007_zps19913f8a.jpg Corners I just had to "wing it" lol. It can be painted, should I ever decide to, I wanted to wait to be sure it would hold, and after 2 years, I'm satisfied it will (has). photo P9080001_zpsb1d6d2f2.jpg Console seat base painted, and door added. It's split in middle, seat raises for upper storage, lower door for bottom storage. photo P9150005_zpsbcecec6f.jpg New shoes photo P9100001_zpsxtfcqkab.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    photo P9150006_zpse25a0463.jpg Gauge panel, switch panel, and console Hummingbird 859 HD installed photo 20150929_144335_zpslhm6sfnn.jpg Start and accessory batteries with disconnects photo PB060022_zpske7isz5i.jpg photo PB060019_zpsvszn8nde.jpg 3-series 29's under console (in old ski locker) for MinnKota Terrova #112 with I-Pilot photo PB040011_zpsifmzz6c6.jpg looking down from seat on front of console, NOCO 3 Bank/30 Amp charger photo PB040010_zpsunajzvpf.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    photo PB040012_zps2xnoiec2.jpg photo PB040007_zpsemthmigk.jpg Made spot for tools and spray bottle for cleaning screen on FF photo PA080001_zpsqdox3eyb.jpg Have a H'Bird 859 HD/DI on bow, so couldn't use the US2 'ducer in trolling motor, so made a separate mount for it, off one of the rod holders (no more holes in deck than necessary). photo PA090005_zpswygg00zc.jpg photo PA020003_zpsoazimomq.jpg Lining-up cap lets me know 'ducer is pointed in correct direction. photo PA090004_zpswzj0qxal.jpg
  • Team36Grit
    Team36Grit Member Posts: 68 ✭✭
    PVC Rod holders (for road travel), hold 12-14' rods photo PA140001_zpso31e1wr5.jpg NOCO 2-Bank 10amp charger for start and accessory (electronics) batteries. photo PB060001_zpsy3ys32ze.jpg Stereo speakers installed photo PB060002_zpse9kty1ib.jpg Still need to get 3 seat pads made, but not having much luck finding anyone local who likes making money. Probably end-up buying a machine and sewing my own, and probably for less than it would cost to pay someone to do it.