Thank you so much for your involvement with the Owner's Club Forum! We hope you've gotten some great information and had the chance to interact with other owners on the current system.
Cup Holders
Comments
-
I do like them a lot!
-
Here's who makes on the ones on my 2014 http://www.itc-marine.com/
-
Anyone know of a stainless steel cup holder that will really fit a 3-3/4" diameter hole? I've tried 2 different stainless steel cup holders with the first one being too small and the second try too large. The plastic cup holders I have now fit perfectly and are snug. I would like to replace all 7 plastic cup holders with stainless steel to class up the boat a bit. But, I won't bother if I have to enlarge the existing holes to make them fit.
1999 Fundeck GS-201, Teal, Honda 200HP -
Check out these made by ITC Marine and see if they might be what you have. They are the exact ones used on my boat. There is a dimension chart that should be useful.
http://www.itc-marine.com/product/stepped-bottom-stainless-steel-drink-holder/
2012 SD237 I/O Mercruiser 5.0L MPI ECT/ Bravo 32012 Load Rite Elite Tandem axle trailer -
Thanks cjjdeck. Do you know if the cup holder holes in your boat are 3-3/4 inches? Looks like a nice cup holder.
1999 Fundeck GS-201, Teal, Honda 200HP -
I think I bought mine from amazon, per the recommendations above & like them a lot. They came with 2 sided tape under the lip that sits on the surface you are mounting to to secure them. They were a standard size as the white plastics that came with it & blow out when towing.
-
I haven't pulled any of the cup holders from the hull to actually measure the hole size, but I have 4 1/4" measurement across the top of mine and the drawing on ITC's website shows a dimension of 3.662" at the base of the cup holder. I would imagine the hole size is easily 3 3/4". That leaves a 1/4" lip around the edge for the foam tape to seal to.DavidPJ said:Thanks cjjdeck. Do you know if the cup holder holes in your boat are 3-3/4 inches? Looks like a nice cup holder.
2012 SD237 I/O Mercruiser 5.0L MPI ECT/ Bravo 32012 Load Rite Elite Tandem axle trailer -
instymp said:I think I bought mine from amazon, per the recommendations above & like them a lot. They came with 2 sided tape under the lip that sits on the surface you are mounting to to secure them. They were a standard size as the white plastics that came with it & blow out when towing.
Thanks instymp. I can't find anything in this thread that indicates which cup from Amazon was being referred to in the above posts. Is this the one you have?
http://www.amazon.com/Amarine-made-Stainless-Holder-Marine-Camper/dp/B0097MF4DU/ref=sr_1_2?ie=UTF8&qid=1438110919&sr=8-2&keywords=stainless+steel+cup+holders+for+boats
1999 Fundeck GS-201, Teal, Honda 200HP -
cjjdec, looks like it will fit. I'm trying to avoid the hassle of buying/returning any more cup holders until I have a good confidence level that it's going to fit this time. The ITC cup looks it would fit but I wonder if it might be too loose. I like the 316 stainless steel choice. I guess I'll never know for sure until I try one. Thanks again.cjjjdeck said:
I haven't pulled any of the cup holders from the hull to actually measure the hole size, but I have 4 1/4" measurement across the top of mine and the drawing on ITC's website shows a dimension of 3.662" at the base of the cup holder. I would imagine the hole size is easily 3 3/4". That leaves a 1/4" lip around the edge for the foam tape to seal to.DavidPJ said:Thanks cjjdeck. Do you know if the cup holder holes in your boat are 3-3/4 inches? Looks like a nice cup holder.
1999 Fundeck GS-201, Teal, Honda 200HP -
